FANUC M-Codes List for 16i, 18i, and More

M-code are CNC program instructions which help machinists and CNC programmers control CNC hardware like chuck, tailstock, quill, coolant. Here are listed M-code which are mostly used on 16i and 18i FANUC Controls.

Auxiliary Function (M Function)

When a numeral is specified following address M, code signal and a strobe signal are sent to the machine. The machine uses these signals to turn on or off its functions. Usually, only one M code can be specified in one block.

In some cases, however, up to three M codes can be specified for some types of machine tools. Which M code corresponds to which machine function is determined by the machine tool builder.

The machine processes all operations specified by M codes except those specified by M98, M99,M198 or called subprogram(Parameter No.6071 to 6079), or called custom macro (Parameter No.6080 to 6089). Refer to the machine tool builder’s instruction manual for details.

The following M codes have special meanings:

  • M02, M03 (End of Program)
    • This indicates the end of the main program Automatic operation is stopped and the CNC unit is reset.
    • This differs with the machine tool builder. After a block specifying the end of the program is executed, control returns to the start of the program. Bit 5 of parameter 3404 (M02) or bit 4 of parameter 3404 (M30) can be used to disable M02, M30 from returning control to the start of the program.
  • M00 (Program Stop)
    • Automatic operation is stopped after a block containing M00 is executed. When the program is stopped, all existing modal information remains unchanged. The automatic operation can be restarted by actuating the cycle operation. This differs with the machine tool builder.
  • M01 (Optional Stop)
    • Similarly to M00, automatic operation is stopped after a block containing M01 is executed. This code is only effective when the Optional Stop switch on the machine operator’s panel has been pressed.
  • M98 (Calling of Sub-Program)
    • This code is used to call a subprogram. The code and strobe signals are not sent.
  • M99 (End of Subprogram)
    • This code indicates the end of a subprogram. M99 execution returns control to the main program. The code and strobe signals are not sent.
  • M198 (Calling a Subprogram)
    • This code is used to call a subprogram of a file in the external input/output function. See the description of the subprogram call function (III–4.7) for details.

 

Multiple M Commands in a Single Block

In general, only one M code can be specified in a block. However, up to three M codes can be specified at once in a block by setting bit 7 (M3B) of parameter No. 3404 to 1. Up to three M codes specified in a block are simultaneously output to the machine. This means that compared with the conventional method of a single M command in a single block, a shorter cycle time can be realized in machining.

CNC allows up to three M codes to be specified in one block. However, some M codes cannot be specified at the same time due to mechanical operation restrictions. For detailed information about the mechanical operation restrictions on simultaneous specification of multiple M codes in one block, refer to the manual of each machine tool builder. M00, M01, M02, M30, M98, M99, or M198 must not be specified together with another M code. Some M codes other than M00, M01, M02, M30, M98, M99, and M198 cannot be specified together with other M codes; each of those M codes must be specified in a single block.

Such M codes include these which direct the CNC to perform internal operations in addition to sending the M codes themselves to the machine. To be specified, such M codes are M codes for calling program numbers 9001 to 9009 and M codes for disabling advance reading (buffering) of subsequent blocks. Meanwhile, multiple of M codes that direct the CNC only to send the M codes themselves (without performing internal operations ) can be specified in a single block.

M Code Group Check Function

The M code group check function checks if a combination of multiple M codes (up to three M codes) contained in a block is correct.

This function has two purposes. One is to detect if any of the multiple M codes specified in a block include an M code that must be specified alone. The other purpose is to detect if any of the multiple M codes specified in a block include M codes that belong to the same group. In either of these cases, P/S alarm No. 5016 is issued. For details on group data setting, refer to the manual available from the machine tool builder.

  • M Code Setting
    • Up to 500 M codes can be specified. In general, M0 to M99 are always specified. M codes from M100 and up are optional.
  • Group Numbers
    • Group numbers can be set from 0 to 127. Note, however, that 0 and 1 have special meanings. Group number 0 represents M codes that need not be checked. Group number 1 represents M codes that must be specified alone.

 

Leave a Reply

Your email address will not be published. Required fields are marked *