{"id":1280,"date":"2016-12-22T12:09:29","date_gmt":"2016-12-22T17:09:29","guid":{"rendered":"https:\/\/www.mroelectric.com\/blog\/?p=1280"},"modified":"2020-03-05T11:08:41","modified_gmt":"2020-03-05T16:08:41","slug":"yaskawa-gpd-503-drives","status":"publish","type":"post","link":"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/","title":{"rendered":"Yaskawa GPD 503 Drives"},"content":{"rendered":"

Installation of Yaskawa<\/a> GPD 503 Drives<\/a>:<\/strong><\/p>\n

1. Be certain your input voltage source, motor, and drive name plates are all marked either 230V, 460V, or 575V. Other voltages can be used, but they require additional programming.<\/p>\n

2. Mount drive on vertical surface with adequate space for air circulation.<\/p>\n

3. Remove front cover, fit conduit to bottom plate, and connect power and ground wires.<\/p>\n

Caution: Be certain you connect power to terminals L1, L2, and L3 only, or serious damage will result. Connect motor to T1, T2, and T3 only.<\/em><\/p>\n

\n

Installation of External Run\/Stop Switch and Speed Potentiators:<\/strong><\/p>\n

Important: Complete the Installation and Keypad Operation before attempting external control.
\n<\/em><\/p>\n

    \n
  1. Disconnect power, remove cover, and wait for “CHARGE” light to go out.<\/li>\n
  2. Connect a switch to terminals 1 and 11 using two conductor shielded wire. This circuit is 24Vdc, very low current; use a quality rotary or toggle switch (all wire should be 14-18AWG). Connect the shield to terminal 12 on the drive end only.<\/li>\n
  3. Install a single conductor “jumper wire” between drive terminals 5 and 11.<\/li>\n
  4. Connect a manual speed potentiometer rated 2000-3000 ohms, 1 watt minimum, using three conductor shielded wire, with shield connected at terminal 12. Connect wires to the potentiometer. Trace wire closest to the top and connect to terminal 17. Trace center wire of potentiometer through and connect to terminal 16. The remaining wire will be connected to the trim pot in step 5.<\/li>\n
  5. Connect a trim potentiometer rated 2000-3000 ohms, 1 watt minimum, as close to the drive terminals as possible. Viewing the potentiometer from the back, connect a single conductor wire from the left terminal to terminal 15 of the drive. Connect a short jumper wire between the center and left terminals. Connect remaining wire from manual speed pot as shown.
    \n
    Check out our other Yaskawa products, including GPD-505<\/a> and GPD-506<\/a> drives!<\/h6>\n
    MRO Electric and Supply Company carried new and remanufactured Yaskawa GPD 503 Drives<\/a>. To place an order or for more information, call 800-691-8511 or email sales@mroelectric.com<\/a>.<\/h6>\n

    \"Yaskawa
    Yaskawa GPD 503 Drives<\/figcaption><\/figure><\/li>\n<\/ol>\n","protected":false},"excerpt":{"rendered":"

    Installation of Yaskawa GPD 503 Drives: 1. Be certain your input voltage source, motor, and drive name plates are all marked either 230V, 460V, or 575V. Other voltages can be used, but they require additional programming. 2. Mount drive on vertical surface with adequate space for air circulation. 3. Remove front cover, fit conduit to […]<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_lmt_disableupdate":"","_lmt_disable":"","_exactmetrics_skip_tracking":false,"_exactmetrics_sitenote_active":false,"_exactmetrics_sitenote_note":"","_exactmetrics_sitenote_category":0,"ngg_post_thumbnail":0,"footnotes":""},"categories":[12,94],"tags":[85],"class_list":["post-1280","post","type-post","status-publish","format-standard","hentry","category-troubleshooting-and-repair","category-yaskawa","tag-motors-and-drives"],"yoast_head":"\nYaskawa GPD 503 Drives - Installation and Instruction<\/title>\n<meta name=\"description\" content=\"Installation of Yaskawa GPD 503 Drives: Be certain your input voltage source, motor, and drive name plates are all marked either 230V, 460V, or 575V.\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Yaskawa GPD 503 Drives\" \/>\n<meta property=\"og:description\" content=\"Installation of Yaskawa GPD 503 Drives: Be certain your input voltage source, motor, and drive name plates are all marked either 230V, 460V, or 575V.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/\" \/>\n<meta property=\"og:site_name\" content=\"MRO Electric Blog\" \/>\n<meta property=\"article:publisher\" content=\"https:\/\/www.facebook.com\/mroelectric\/\" \/>\n<meta property=\"article:published_time\" content=\"2016-12-22T17:09:29+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2020-03-05T16:08:41+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/www.mroelectric.com\/blog\/wp-content\/uploads\/2016\/12\/gpd503-4l75.jpg\" \/>\n<meta name=\"author\" content=\"Joe Kaminski\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:creator\" content=\"@mroelectric\" \/>\n<meta name=\"twitter:site\" content=\"@mroelectric\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"Joe Kaminski\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"2 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":\"Article\",\"@id\":\"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/#article\",\"isPartOf\":{\"@id\":\"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/\"},\"author\":{\"name\":\"Joe Kaminski\",\"@id\":\"https:\/\/www.mroelectric.com\/blog\/#\/schema\/person\/b993515a2417163a23dfe88597c8d13a\"},\"headline\":\"Yaskawa GPD 503 Drives\",\"datePublished\":\"2016-12-22T17:09:29+00:00\",\"dateModified\":\"2020-03-05T16:08:41+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/\"},\"wordCount\":334,\"commentCount\":0,\"publisher\":{\"@id\":\"https:\/\/www.mroelectric.com\/blog\/#organization\"},\"image\":{\"@id\":\"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/#primaryimage\"},\"thumbnailUrl\":\"https:\/\/www.mroelectric.com\/blog\/wp-content\/uploads\/2016\/12\/gpd503-4l75.jpg\",\"keywords\":[\"Motors & Drives\"],\"articleSection\":[\"Troubleshooting & Repair\",\"Yaskawa\"],\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/#respond\"]}]},{\"@type\":\"WebPage\",\"@id\":\"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/\",\"url\":\"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/\",\"name\":\"Yaskawa GPD 503 Drives - Installation and Instruction\",\"isPartOf\":{\"@id\":\"https:\/\/www.mroelectric.com\/blog\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/#primaryimage\"},\"image\":{\"@id\":\"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/#primaryimage\"},\"thumbnailUrl\":\"https:\/\/www.mroelectric.com\/blog\/wp-content\/uploads\/2016\/12\/gpd503-4l75.jpg\",\"datePublished\":\"2016-12-22T17:09:29+00:00\",\"dateModified\":\"2020-03-05T16:08:41+00:00\",\"description\":\"Installation of Yaskawa GPD 503 Drives: Be certain your input voltage source, motor, and drive name plates are all marked either 230V, 460V, or 575V.\",\"breadcrumb\":{\"@id\":\"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/#primaryimage\",\"url\":\"https:\/\/www.mroelectric.com\/blog\/wp-content\/uploads\/2016\/12\/gpd503-4l75.jpg\",\"contentUrl\":\"https:\/\/www.mroelectric.com\/blog\/wp-content\/uploads\/2016\/12\/gpd503-4l75.jpg\",\"width\":400,\"height\":372,\"caption\":\"Yaskawa GPD 503 Drives\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/www.mroelectric.com\/blog\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Yaskawa GPD 503 Drives\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/www.mroelectric.com\/blog\/#website\",\"url\":\"https:\/\/www.mroelectric.com\/blog\/\",\"name\":\"MRO Electric Blog\",\"description\":\"Applications of PLCs, CNCs, and more!\",\"publisher\":{\"@id\":\"https:\/\/www.mroelectric.com\/blog\/#organization\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\/\/www.mroelectric.com\/blog\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"en-US\"},{\"@type\":\"Organization\",\"@id\":\"https:\/\/www.mroelectric.com\/blog\/#organization\",\"name\":\"MRO Electric and Supply\",\"url\":\"https:\/\/www.mroelectric.com\/blog\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\/\/www.mroelectric.com\/blog\/#\/schema\/logo\/image\/\",\"url\":\"https:\/\/www.mroelectric.com\/blog\/wp-content\/uploads\/mro-logo-new_large2_blue-1.png\",\"contentUrl\":\"https:\/\/www.mroelectric.com\/blog\/wp-content\/uploads\/mro-logo-new_large2_blue-1.png\",\"width\":430,\"height\":222,\"caption\":\"MRO Electric and Supply\"},\"image\":{\"@id\":\"https:\/\/www.mroelectric.com\/blog\/#\/schema\/logo\/image\/\"},\"sameAs\":[\"https:\/\/www.facebook.com\/mroelectric\/\",\"https:\/\/x.com\/mroelectric\"]},{\"@type\":\"Person\",\"@id\":\"https:\/\/www.mroelectric.com\/blog\/#\/schema\/person\/b993515a2417163a23dfe88597c8d13a\",\"name\":\"Joe Kaminski\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\/\/www.mroelectric.com\/blog\/#\/schema\/person\/image\/\",\"url\":\"https:\/\/secure.gravatar.com\/avatar\/fb7c0d641ed541ad912b27609e8079304fc356be7b5b53578b32ad3fa973f506?s=96&d=mm&r=g\",\"contentUrl\":\"https:\/\/secure.gravatar.com\/avatar\/fb7c0d641ed541ad912b27609e8079304fc356be7b5b53578b32ad3fa973f506?s=96&d=mm&r=g\",\"caption\":\"Joe Kaminski\"},\"description\":\"Joe Kaminski is an industrial automation specialist at MRO Electric. He has a background in industrial engineering and supply chain management. Joe has worked in the automation industry for over 10 years providing support to some of the largest companies in the world. For more info, visit www.mroelectric.com.\",\"url\":\"https:\/\/www.mroelectric.com\/blog\/author\/jadmin\/\"}]}<\/script>\n<!-- \/ Yoast SEO Premium plugin. -->","yoast_head_json":{"title":"Yaskawa GPD 503 Drives - Installation and Instruction","description":"Installation of Yaskawa GPD 503 Drives: Be certain your input voltage source, motor, and drive name plates are all marked either 230V, 460V, or 575V.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/","og_locale":"en_US","og_type":"article","og_title":"Yaskawa GPD 503 Drives","og_description":"Installation of Yaskawa GPD 503 Drives: Be certain your input voltage source, motor, and drive name plates are all marked either 230V, 460V, or 575V.","og_url":"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/","og_site_name":"MRO Electric Blog","article_publisher":"https:\/\/www.facebook.com\/mroelectric\/","article_published_time":"2016-12-22T17:09:29+00:00","article_modified_time":"2020-03-05T16:08:41+00:00","og_image":[{"url":"https:\/\/www.mroelectric.com\/blog\/wp-content\/uploads\/2016\/12\/gpd503-4l75.jpg","type":"","width":"","height":""}],"author":"Joe Kaminski","twitter_card":"summary_large_image","twitter_creator":"@mroelectric","twitter_site":"@mroelectric","twitter_misc":{"Written by":"Joe Kaminski","Est. reading time":"2 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/#article","isPartOf":{"@id":"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/"},"author":{"name":"Joe Kaminski","@id":"https:\/\/www.mroelectric.com\/blog\/#\/schema\/person\/b993515a2417163a23dfe88597c8d13a"},"headline":"Yaskawa GPD 503 Drives","datePublished":"2016-12-22T17:09:29+00:00","dateModified":"2020-03-05T16:08:41+00:00","mainEntityOfPage":{"@id":"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/"},"wordCount":334,"commentCount":0,"publisher":{"@id":"https:\/\/www.mroelectric.com\/blog\/#organization"},"image":{"@id":"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/#primaryimage"},"thumbnailUrl":"https:\/\/www.mroelectric.com\/blog\/wp-content\/uploads\/2016\/12\/gpd503-4l75.jpg","keywords":["Motors & Drives"],"articleSection":["Troubleshooting & Repair","Yaskawa"],"inLanguage":"en-US","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/#respond"]}]},{"@type":"WebPage","@id":"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/","url":"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/","name":"Yaskawa GPD 503 Drives - Installation and Instruction","isPartOf":{"@id":"https:\/\/www.mroelectric.com\/blog\/#website"},"primaryImageOfPage":{"@id":"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/#primaryimage"},"image":{"@id":"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/#primaryimage"},"thumbnailUrl":"https:\/\/www.mroelectric.com\/blog\/wp-content\/uploads\/2016\/12\/gpd503-4l75.jpg","datePublished":"2016-12-22T17:09:29+00:00","dateModified":"2020-03-05T16:08:41+00:00","description":"Installation of Yaskawa GPD 503 Drives: Be certain your input voltage source, motor, and drive name plates are all marked either 230V, 460V, or 575V.","breadcrumb":{"@id":"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/"]}]},{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/#primaryimage","url":"https:\/\/www.mroelectric.com\/blog\/wp-content\/uploads\/2016\/12\/gpd503-4l75.jpg","contentUrl":"https:\/\/www.mroelectric.com\/blog\/wp-content\/uploads\/2016\/12\/gpd503-4l75.jpg","width":400,"height":372,"caption":"Yaskawa GPD 503 Drives"},{"@type":"BreadcrumbList","@id":"https:\/\/www.mroelectric.com\/blog\/yaskawa-gpd-503-drives\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/www.mroelectric.com\/blog\/"},{"@type":"ListItem","position":2,"name":"Yaskawa GPD 503 Drives"}]},{"@type":"WebSite","@id":"https:\/\/www.mroelectric.com\/blog\/#website","url":"https:\/\/www.mroelectric.com\/blog\/","name":"MRO Electric Blog","description":"Applications of PLCs, CNCs, and more!","publisher":{"@id":"https:\/\/www.mroelectric.com\/blog\/#organization"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/www.mroelectric.com\/blog\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"en-US"},{"@type":"Organization","@id":"https:\/\/www.mroelectric.com\/blog\/#organization","name":"MRO Electric and Supply","url":"https:\/\/www.mroelectric.com\/blog\/","logo":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/www.mroelectric.com\/blog\/#\/schema\/logo\/image\/","url":"https:\/\/www.mroelectric.com\/blog\/wp-content\/uploads\/mro-logo-new_large2_blue-1.png","contentUrl":"https:\/\/www.mroelectric.com\/blog\/wp-content\/uploads\/mro-logo-new_large2_blue-1.png","width":430,"height":222,"caption":"MRO Electric and Supply"},"image":{"@id":"https:\/\/www.mroelectric.com\/blog\/#\/schema\/logo\/image\/"},"sameAs":["https:\/\/www.facebook.com\/mroelectric\/","https:\/\/x.com\/mroelectric"]},{"@type":"Person","@id":"https:\/\/www.mroelectric.com\/blog\/#\/schema\/person\/b993515a2417163a23dfe88597c8d13a","name":"Joe Kaminski","image":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/www.mroelectric.com\/blog\/#\/schema\/person\/image\/","url":"https:\/\/secure.gravatar.com\/avatar\/fb7c0d641ed541ad912b27609e8079304fc356be7b5b53578b32ad3fa973f506?s=96&d=mm&r=g","contentUrl":"https:\/\/secure.gravatar.com\/avatar\/fb7c0d641ed541ad912b27609e8079304fc356be7b5b53578b32ad3fa973f506?s=96&d=mm&r=g","caption":"Joe Kaminski"},"description":"Joe Kaminski is an industrial automation specialist at MRO Electric. He has a background in industrial engineering and supply chain management. Joe has worked in the automation industry for over 10 years providing support to some of the largest companies in the world. For more info, visit www.mroelectric.com.","url":"https:\/\/www.mroelectric.com\/blog\/author\/jadmin\/"}]}},"modified_by":"Brian Hughes","_links":{"self":[{"href":"https:\/\/www.mroelectric.com\/blog\/wp-json\/wp\/v2\/posts\/1280","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.mroelectric.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.mroelectric.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.mroelectric.com\/blog\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.mroelectric.com\/blog\/wp-json\/wp\/v2\/comments?post=1280"}],"version-history":[{"count":6,"href":"https:\/\/www.mroelectric.com\/blog\/wp-json\/wp\/v2\/posts\/1280\/revisions"}],"predecessor-version":[{"id":4496,"href":"https:\/\/www.mroelectric.com\/blog\/wp-json\/wp\/v2\/posts\/1280\/revisions\/4496"}],"wp:attachment":[{"href":"https:\/\/www.mroelectric.com\/blog\/wp-json\/wp\/v2\/media?parent=1280"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.mroelectric.com\/blog\/wp-json\/wp\/v2\/categories?post=1280"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.mroelectric.com\/blog\/wp-json\/wp\/v2\/tags?post=1280"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}