On the top of Siemens Simodrive UE and I/R modules there is a series of 6 dipswitches that need to be set correctly before starting up your drive. Below is the table showing the switch settings along with info on the specific switches so you know what the correct Simodrive Dipswitch Settings for your system are.
Note: For I/R modules Order No. 6SN114–10–01 the basic setting is for
sinusoidal control (closed–loop). Observe the information/instructions, Page
NE1–3!
Note: Before the equipment is powered–up or down using the main switch or a line contactor, terminal 63 (pulse enable) and/or terminal 48 (start terminal, contactor control) should be de–energized or disconnected!
| Switch S 1.1 : | OFF: | I/R module Vsupply =400V10%; VDC link=600V |
| UE module Vsupply =400V10%; VDC link=1.35*Vsupply | ||
| monitoring thresholds: (I/R, UE–, monitoring modules) | ||
| pulsed resistor on =644V; pulsed resistor off =618V | ||
| VDC link>> =710V; | ||
| ON: | I/R module Vsupply =415V10%; VDC link=625V | |
| UE module Vsupply =415V10%; VDC link=1.35*Vsupply | ||
| Monitoring thresholds: (I/R–, UE–, monitoring modules) | ||
| pulsed resistor on =670V; pulsed resistor off =640V | ||
| VDC link>> =740V; | ||
| Switch S 1.2 : | OFF: | Ready signal (X111 ready relay) |
| For S1.2=OFF, the relay switches if the following | ||
| conditions are fulfilled: | ||
| – internal main contactor CLOSED (terminals NS1–NS2 connected, | ||
| terminal 48 | ||
| enabled) | ||
| – terminal 63,64=ENERGIZED | ||
| – no fault present (also not on feed drive 611A Standard, | ||
| or 611D drives) | ||
| – feed drive with standard interface or resolver for setting | ||
| ”Ready” is enabled (terminals 663,65) | ||
| ON: | Fault message (X111 ready relay) | |
| For S1.2=ON, the relay switches if the following | ||
| conditions are fulfilled: | ||
| – internal main contactor CLOSED (terminals NS1–NS2 connected, | ||
| terminal 48 | ||
| enabled) | ||
| – no fault present (also not on feed drive 611A Standard, | ||
| or 611D drives) | ||
| – feed drive with standard interface or resolver for setting | ||
| ”ready” is enabled (terminals 663,65); | ||
| Switch S 1.3 : | OFF: | Standard setting, regenerative feedback active |
| I/R modules are capable of regenerative feedback | ||
| UE modules: The pulsed resistor in the module is effective | ||
| ON: | Regenerative feedback switched–out (disabled) | |
| I/R module: Regenerative feedback operation is inhibited | ||
| UE modules: The pulsed resistor in the module is not | ||
| effective | ||
| Switch S 1.4 : | OFF: | Standard setting for all NE modules, refer to S1.1 |
| ON: | Vsupply =480V+6%–10%; VDC link=1.35*Vsupply in the infeed direction | |
| Monitoring thresholds: (I/R, UE, monitoring modules) | ||
| pulsed resistor on =744V; pulsed resistor off =718V | ||
| VDC link>> =795V. | ||
| Switch S 1.5 : | OFF: | Standard setting, controlled infeed active. |
| ON: | Uncontrolled operation in the infeed direction VDC link=1.35*Vsupply . | |
| Regenerative feedback operation is initiated at V DC link=600 or 625V, | ||
| depending on the setting of S1.1 . | ||
| Switch S 1.6 : | OFF: | Square–wave current control (square–wave current is drawn from the |
| line supply) | ||
| ON: | This function is only available in conjunction with I/R modules | |
| 6SN114–10–01 | ||
| Sinusoidal current control (sinusoidal current is drawn from the line | ||
| supply) |
For more info, give us a call at 800-691-8511 or email sales@mroelectric.com. Our full Simodrive series is listed here.
Updated on June 25, 2019 by Ryan Dickinson
what is ia relay in u/e 6sn1145 power module